How to Install a Bath Tub
How to Install a Bath Tub
Blog Article
Do you find yourself trying to locate answers around How to Install a Bathtub: Install an Acrylic Tub and Tub Surround?
Installing a bathtub isn't precisely rocket science, but it does call for solid plumbing, carpentry, and also occasionally, tiling abilities. Changing an old tub with a new one is also a reasonably hard job. If the old tub is readily obtainable, the job can move easily; if you have to open a wall surface to remove the old bathtub as well as position the brand-new tub, the task is a lot harder. In either case, the task is within a house handyman's skills, although you will need an assistant to move out the old bathtub as well as embeded in the new one. See to it you have actually qualified on your own for the job and also are comfortable trying it. Instead of hiring a specialist to take over a halfway-completed project, it is far better to take into consideration utilizing one before you start. Possibilities are you might require a professional plumber to make tube links.
This post will assist you install a brand-new tub in your restroom if you have currently gotten a brand-new bathtub and also do not need to change the plan of your previous supply of water pipelines.
Your devices and material list ought to make up the following:
Preparing for the Setup
To start with, the sustaining structure provided with the bathroom must be fitted (if needed) according to the producer's guidelines. Next off, fit the taps or mixer to the tub. When fitting the faucet block, it is very important to ensure that if the tap includes a plastic washer, it is fitted between the bathroom as well as the taps. On a plastic bathroom, it is likewise reasonable to fit a sustaining plate under the faucets unit to prevent strain on the tub.
Fit the versatile tap ports to the bottom of the two faucets using 2 nuts as well as olives (in some cases supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and then pass the electrical outlet with the hole in the bathroom. Make use of the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit the end of the adaptable overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Connect all-time low of the overflow tube in a similar manner.The bathroom must currently be ready to be suited its final placement.
Removing Old Taps
If you require to replace old faucets with new ones as a part of your setup, then the first thing you must do is separate the water system. After doing so, activate the taps to drain pipes any water staying in the system. The procedure of eliminating the existing faucets can be quite troublesome due to the restricted accessibility that is typically the instance.
Use a container wrench (crowsfoot spanner) or a tap tool to reverse the nut that connects the supply pipes to the faucets. Have a cloth prepared for the continuing to be water that will certainly come from the pipes. When the supply pipelines have been eliminated, use the exact same device to loosen up the nut that holds the taps onto the bath/basin. You will certainly need to stop the single taps from turning throughout this process. As soon as the taps have been eliminated, the holes in the bath/basin will certainly have to be cleaned of any kind of old sealing substance.
Prior to going on to fit the brand-new faucets, compare the pipe connections on the old taps to the brand-new faucets. If the old faucets are longer than the new taps, after that a shank adapter is needed for the new taps to fit.
Installing the Bath tub
Using the two wood boards under its feet, put the tub in the required position. The wood boards are practical in uniformly spreading the weight of the bathtub over the location of the boards as opposed to focusing all the weight onto four tiny factors.
The following goal is to ensure that the tub is leveled all round. This can be accomplished by checking the level as well as readjusting the feet on the tub until the level reads level.
To mount faucets, fit the bottom of the outermost flexible faucet connector to the proper supply pipe by making a compression sign up with; after that do the exact same for the various other tap.
Activate the supply of water and also examine all joints and also new pipework for leaks as well as tighten them if essential. Fill the tub as well as also check the overflow electrical outlet and also the regular outlet for leaks.
Lastly, take care of the bathroom paneling as defined in the manufacturer's instruction manual. Tiling as well as securing around the bathtub must wait up until the bath tub has actually been used a minimum of once as this will settle it into its final setting.
Suitable New Touches
If the tails of the brand-new faucets are plastic, after that you will certainly need a plastic connector to prevent damage to the thread. One end of the connector fits on the plastic tail of the tap as well as the other end offers a link to the existing supply pipes.
If you need to fit a monobloc, after that you will need decreasing couplers, which connects the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making sure that the washers are in area in between the tap and the sink. Safeguard the faucet in place with the manufacturer provided backnut. As soon as the faucet is securely in place, the supply pipelines can be linked to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal faucet ports. The former kind must be connected to the faucet finishes initially, tightening up just by hand. The supply pipelines can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been connected.
Tiling Around the Tub
In the area where the bathroom meets the tile, it is needed to seal the accompanies a silicone rubber caulking. This is necessary as the fitting can relocate enough to crack an inflexible seal, triggering the water to pass through the wall surface between the bathroom and the tiling, bring about issues with dampness and also possible leakages to the ceiling below.
You can pick from a selection of coloured sealers to blend in your components and installations. They are sold in tubes and also cartridges, and can sealing voids up to a width of 3mm (1/8 inch). If you have a bigger gap to fill up, you can load it with spins of soaked paper or soft rope. Bear in mind to always fill up the bath tub with water before sealing, to enable the activity experienced when the tub is in usage. The sealer can crack relatively very early if you do not take into consideration this activity before sealing.
Additionally, ceramic coving or quadrant floor tiles can be made use of to edge the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are also quickly offered on the marketplace. It is advisable to fit the tiles utilizing water-resistant or water-proof glue and also grout.
A Step-by-Step Guide to Installing a Bathtub
Is your bathtub looking a bit dated lately? Believe it or not, installing a new one is a project you can do yourself. Whether your bathtub is broken or doesn’t fit in with your current bathroom’s design, you can fix it without having to hire a contractor or paying labour costs.
But, beyond saving money, there are other benefits of installing your own bathtub. When you do this project yourself, you can customise every step of the process. You can also make sure the finished product looks exactly the way you want it to.
This DIY project is quite involved, but by doing some research, preparing your bathroom and using the right equipment, it is definitely one you can take on. This guide will help you understand the technical procedures behind installing a new bathtub.
Remove the Existing Bathtub
To remove the old bathtub, you will need to turn the water supply off before you start any work. After you turn the water off, there will likely still be some water left in your plumbing system, which you can remove by turning on a faucet below the level of the bathtub. Once the water stops running, you are ready to start working.
The easiest way to remove the tub is to remove the faucet, handles and other piping and then pull the tub out from the wall. If this doesn’t work in your situation, you will need to remove part of the wall, remove the piping and then slide the tub out.
Choose the Right Bathtub
The ideal way to replace your bathtub is to find one that has the exact dimensions and has the drain and faucet on the same side as your old one. This way, it will fit in the same place and you won’t have to change the piping system in your bathroom. Choose a tub that matches your home’s decor and fits with the style of the bathroom.
Install the Plumbing and Ledger Board
You can purchase a tub drain kit at a hardware store which will have all the pieces you will need for your new tub’s plumbing. Follow the instructions that came with the kit to install the plumbing in the new tub and then take measurements to make sure the plumbing in the tub will align with the plumbing in your bathroom. If it doesn’t, now is the time to make necessary adjustments.
Some bathtubs need a ledger board that is installed on the wall behind the tub to help support it. If your new bathtub requires one, the directions that came with it will tell you how high it should be installed. If your old bathtub had a ledger board, and it is still in good condition, you can adjust its height to match the new bathtub.
Install the Bathtub
When the plumbing and ledger board are ready, you can install the new bathtub. Carefully lower it into the space, being careful not to damage the tub, wall, plumbing or ledger board. Since bathtubs are very heavy and you will need to line the tub up exactly, it is wise to have someone help you with this step.
Once the tub is in place, it needs to be perfectly level, so use a bubble level instead of estimating how level the tub is. Put the level on the top edge of the tub, not the bottom on the inside, since many tubs are designed with a sloped bottom.
If the bathtub isn’t level, adjust the ledger board and shift the tub until it is. When it is level, use screws to attach the tub to the wall studs. Most bathtubs have pre-drilled holes in the upper flange, so use these but do not over tighten the screws.
Hook up the Plumbing
Now that the bathtub is installed, it needs to be attached to your plumbing system. First, install the shoe fitting under the tub and drain pipe, then the overflow pipe and then the drain flange. Your tub plumbing kit will include specific instructions on how to install these pieces.
Install the Bathtub Surround
A bathtub surround will protect the walls around the tub from water damage and can give your new bathtub a more finished look. To install one, make sure the wall is completely clean and dry so that the adhesive will be able to hold the surround securely. Then, measure the surround and mark the same dimensions on the wall above the tub.
Following the directions that came with the surround adhesive, apply it to the wall. Press the surround against the wall on top of the adhesive and then pull it away for about three minutes to activate the adhesive, then apply the surround again. Keep in mind that this is the most common way to use an adhesive, but you should check the instructions on the package for any special steps.
If there is any excessive adhesive around the sides of the surround, you can use mineral spirits to remove it. Then use masking tape to hold the surround panels in place until the adhesive is dry. Using silicone, seal all the cracks between the surround panels and the gap between the bottom of the panels and the top of the bathtub.
If you want to install tile above your bathtub, instead of a bathtub surround, the process will be very similar. But, you will need to measure and cut tiles and install each one individually, using tile spacers to make sure they are evenly spaced. You will then use grout to fill in the spaces between the tiles.
https://www.hss.com/blog/bathroom/a-step-by-step-guide-to-installing-a-bathtub/
We are very interested by Installing A Bathtub and I'm hoping you liked my article. Please take a moment to distribute this post if you enjoyed reading it. I recognize the value of reading our article about A Step-by-Step Guide to Installing a Bathtub.
Get Offer Report this page